Users:General FEM Analysis/Elements Reference/Membrane1

From Carat++ Public Wiki
(Difference between revisions)
Jump to: navigation, search
Line 12: Line 12:
 
* This membrane element is a plane stress element with 3 degrees of freedom per node
 
* This membrane element is a plane stress element with 3 degrees of freedom per node
 
* The membrane element neglects the bending stiffness
 
* The membrane element neglects the bending stiffness
* The ratio of the thickness and the lengths in the other two directions is much smaller than one ( t/Lx << 1 and t/Ly << 1).
+
* The ratio of the thickness and the lengths in the other two directions is much smaller than one ( t/Lx << 1 and t/Ly << 1), the membrane is reduced to its mid-surface
 
* The thickness is constant over the element
 
* The thickness is constant over the element
  
Line 21: Line 21:
 
=== Degrees of Freedom ===
 
=== Degrees of Freedom ===
  
For the membrane element use the 3 translatoric degrees of freedom.
+
The membrane element uses the 3 translatoric degrees of freedom,
''DISP_X, DISP_Y, DISP_Z''
+
''DISP_X, DISP_Y, DISP_Z''.
  
  
Line 48: Line 48:
 
B_X, B_Y, B_Z  
 
B_X, B_Y, B_Z  
 
|
 
|
|Definition of the principle directions of the surface. To define the prestress dirctions. (see description below)
+
|Definition of the principal directions of the surface to define the prestress directions. (see description below)
 
|-
 
|-
 
!SIG11
 
!SIG11
Line 55: Line 55:
 
|
 
|
 
|Prestress state of the membrane. (see description below)
 
|Prestress state of the membrane. (see description below)
 +
|-
 +
|colspan="3" style="background:#efefef;"| Optional Parameters
 +
|-
 +
!Parameter
 +
!Values, Default(*)
 +
!Description
 
|-
 
|-
 
!LAGRANGE
 
!LAGRANGE
Line 60: Line 66:
 
|Definition of lagrange type. UPDATED for form finding and TOTAL for statics or dynamics. (e.g. LAGRANGE=UPDATED)
 
|Definition of lagrange type. UPDATED for form finding and TOTAL for statics or dynamics. (e.g. LAGRANGE=UPDATED)
 
|-
 
|-
|colspan="3" style="background:#efefef;"| Optional Parameters
 
 
|}
 
|}
  
Line 66: Line 71:
 
<pre>
 
<pre>
 
EL-PROP 1 : MEMBRANE1
 
EL-PROP 1 : MEMBRANE1
MAT= EL-MAT 1       THICKNESS=1.0
+
MAT= EL-MAT 1   THICKNESS=1.0
PRESTRESS     SIG11=1.0     SIG22=1.0     SIG12=0.0
+
PRESTRESS   SIG11=1.0 SIG22=1.0 SIG12=0.0
A_X=1.0     A_Y=0.0   A_Z=0.0
+
A_X=1.0 A_Y=0.0 A_Z=0.0
B_X=0.0   B_Y=1.0   B_Z=0.0   
+
B_X=0.0 B_Y=1.0 B_Z=0.0   
 
LAGRANGE=UPDATED
 
LAGRANGE=UPDATED
 
</pre>
 
</pre>

Revision as of 06:37, 5 December 2016


Contents

General Description

Possible Element Types for Membranes


Element Type

  • This membrane element is a plane stress element with 3 degrees of freedom per node
  • The membrane element neglects the bending stiffness
  • The ratio of the thickness and the lengths in the other two directions is much smaller than one ( t/Lx << 1 and t/Ly << 1), the membrane is reduced to its mid-surface
  • The thickness is constant over the element


Degrees of Freedom

The membrane element uses the 3 translatoric degrees of freedom, DISP_X, DISP_Y, DISP_Z.


Input Parameters

Parameter Description

Compulsory Parameters
Parameter Values, Default(*) Description
MAT EL-MAT int Number for the used Material

e.g. MAT=EL-MAT 1

THICKNESS int Thickness of the membrane
A_X, A_Y, A_Z

B_X, B_Y, B_Z

Definition of the principal directions of the surface to define the prestress directions. (see description below)
SIG11

SIG22 SIG12

Prestress state of the membrane. (see description below)
Optional Parameters
Parameter Values, Default(*) Description
LAGRANGE TOTAL, UPDATED Definition of lagrange type. UPDATED for form finding and TOTAL for statics or dynamics. (e.g. LAGRANGE=UPDATED)

Example of a Complete Input Block

EL-PROP 1 : MEMBRANE1
MAT= EL-MAT 1    THICKNESS=1.0
PRESTRESS   SIG11=1.0  SIG22=1.0  SIG12=0.0
A_X=1.0  A_Y=0.0  A_Z=0.0
B_X=0.0  B_Y=1.0  B_Z=0.0  
LAGRANGE=UPDATED


Element Loading

Pressure

Dead Load

Snow Load

Theory

The theory and finite element formulation is described in detail in the work of Dieringer [1] and Linhard [2]

For the correct use of the membrane element and the interpretation of related results, the following aspects should be considered:


Material parameter

With the parameter MAT the material, that would be used in the calculation, for the membrane element is defined. A very popular mistake is that a material number would be used, that isn't defined already. Please ensure that the material that you would like to use at this point are already exits. The following materials are testet for the membrane element:

  • linear elastic isotropic
  • linear elastic orthotropic (Münsch-Reinhardt)
  • multilinear elastic isotropic
  • elastoplastic isotropic
  • material on the basis of response functions

Thickness parameter

The parameter THICKNESS defines the thickness of the membrane. The thickness should be constant over the element.

Prestress directions on the surface

The parameters A_X, A_Y, A_Z and B_X, B_Y, B_Z are used to define the prestress directions on the surface. In this approach the principle directions of the prestress are defined in a plane area (see figure below). The definition of the area is given by the two vectors f1 and f2. The normal vector of the area can be calculated with the cross product of the in plane vectors f3=f1 x f2. Afterwards the line of intersection T1 of the area which is given by f1 and f3 and the curved surface can be calculated. In this approach T1 is interpreted as the first principle direction of the prestress on the curved surface. With the assumption that T3 is equal to the surface normal vector G3 (not uniformed), the second direction of the prestress is calculated as T2=T1 x T3. W.r.t. the parameters for the input file, only the plane area with the vectors f1 and f2 have to be defined. Referring to the depict approach the vector A defines the vector f1 and the vector B defines the vector f2.

Definition of the prestress direction for Membrane

Prestress state &sigma

SIG11, SIG22, SIG12 describes the prestress of the membrane element. The element is based on the plane stress assuption. Due to that only normal and shear stresses in the midplane have to be defined. SIGG11 is the stress acting in T1, SIG22 acting in T2 and SIG12 is the in plane shear, whereas SIG12=SIG21 (see figure below).

Stress state for Membranes

Lagrange type

With the LARANGE parameter it is possible to switch between form finding and statical/dynamical analysis. For the value UPDATED the element is for form finding and for the value TOTAL the element is for statical/dynamical analysis. It is important that the LANGRANGE parameter match to the type of analysis.


References

  1. Dieringer, F.: Implementierung eines geometrisch nichtlinearen Membranelements in einer objektorientierten Programmierumgebung, Masterthesis, Chair of structural analysis, Technische Universität München, 2009
  2. Linhard, J.: Numerisch-mechanische Betrachtung des Entwurfsprozesses von Membrantragwerken, PhD-Thesis, Chair of structural analysis, Technische Universität München, 2009




Whos here now:   Members 0   Guests 0   Bots & Crawlers 1
 
Personal tools
Content for Developers