Users:Structural Optimization/Response Functions/Stress

Revision as of 14:54, 26 October 2010

General Description

Short Info

The Kreisselmeier-Steinhauser function for the stresses is a global measure of stress in a structure. Stress results are generally very local results but using this responce function an overall stress indicator is obtained. It can be used as an objective to reduce the overall stress in the structure or as a constraint to limit the stress in the structure to a maximum allowed value.

The Kreisselmeier-Steinhauser function for the stresses is formulated by

with ∑_i a summation over all Gausspoints in the domain and σ_i the stress in the i-th Gausspoint from a linear or nonlinear analysis. σ_max is the maximum allowed stress. ρ is a parameter that determines the importance of the largest stresses amongst all σ_i. The response function requires the ID of a linear static analysis or a nonlinear static analysis specified for parameter 'ANALYSIS'.

This function was originally designed as a continuous alternative for max(σ_i). The larger ρ, the more KS approaches max(σ_i). For a large ρ, the value of KS depends merely on the maximal stress value so the effect of the function is limited to the neighbourhood of this maximal stress. If ρ is small, KS is always larger than max(σ_i). When reducing ρ the effect of the function becomes more global since more stresses contribute significantly to its value. It is required to specify a value for ρ with the input parameter RHO. A reasonable range of ρ is between 1 and 100.

The value of the exponential function becomes infinite very fast, even for reasonable values of the argument. Therefore, the value of σ_max should not be too small. The best results are obtained if the stresses σ_i are similar to σ_max. If all the stresses in the structure are much smaller than the allowed stress, there will be no reasonable value of ρ that is large enough to make KS similar to max(σ_i). As a consequence, KS will be similar for all proposed structures and thus become useless. If the value of the maximum allowed stress is specified by the paramater STRESS_LIMIT, the formula stated above is used. If a positive value is specified for STRESS_LIMIT, the negative stresses have a very limited contribution to the value of KS. If the value for STRESS_LIMIT is negative, the largest negative stresses determine KS completely. In constrast, if ABS_STRESS_LIMIT is used, the formulation of KS is changed to:

such that both the negative and the positive stresses influence the value of the response function.

So to summarize: if this response function is used as an objective function, the value of σ_max should be chosen such that it is close to the real stresses in the structure. Additionally, the value for ρ should be rather low to obtain a measure of stress with a global effect. If this response function is used as a constraint function, the value of σ_max should be chosen as the real maximum allowed value. If the material has the same stress limit in tension and compression, ABS_STRESS_LIMIT can be used. However, if the limit in tension and compression is different, two constraints should be added with the respective positive and negative STRESS_LIMIT. Using this response function as a constraint is conservative since KS will always be at the safe side. To limit this overdimensioning, it is necessary to choose a sufficient high ρ to be sure that KS is close to max(σ_i). However, ρ should not be too high, since this introduces similar numerical problems as using the discontinuous constraint max(σ_i).

Input Parameters

Example of a Complete Input Block

OPT-RESPONSE_FCT 1 : STRESS_KS

  ! -- basic stuff
  WEIGHT=1.0 ANALYSIS=PC-ANALYSIS 1 ETA=1e-06
  GRAD=ADJOINT SA=SEMI_ANALYTIC FDA=FOREWARD
  DESVAR=OPT-VAR 1,2,3,4,5,6

  ! -- specific
  ELEMENTS = EL-SET 1
  STRESS_TYPE = PRINCIPLE_1_TOP
  RHO = 10.0
  ABS_STRESS_LIMIT = 200.0E06

  ! -- constraint parameters
  ABS_LIMIT = 1-e3
  REL_TOLERANCE = 0.1
  CONSTRAINT_TYPE = INEQUALITY_LT
  LAMBDA_ABS_MAX = 20

Examples

Catenary arch with stress as objective

This example shows the evolution of a circular arch loaded by self weight to a catenary arch during the minimization of the Kreisselmeier-Steinhauser function for the stress. It is clear that the effect of KS is global, even by using local stress results.

Catenary arch with stress as constraint

Consider now the same circular arch but loaded by snowload. By changing the thickness in each node, the mass is minimized. It is assumed that the Von Mises top stress is limited to 1500 MPa. For that reason, the KS function is used as a constraint. Rho is set to 10 in order to have a global effect. Due to the formulation of the KS function, the maximal value of the constraint is expected to be 1. However, based on a preliminary run, the maximal value of the constraint is set to 1.4 to work around the margin that the KS function implies with low values for rho. Starting from a thickness of 0.08 m, the resulting thicknesses are between 0.048 and 0.063 m. The maximal Von Mises top stress is 1496 MPa, which is surprisingly exact. The volume of the structure is reduced about 40%, from 1.25 to 0.87 m3.

Shell cantilever

This example shows the optimal shape of a cantilever beam subjected to an end load. The structure is modelled by shell elements. During the optimization, the Kreisselmeier-Steinhauser function is minimized while the structural weight was not allowed to increase more than 5%. To avoid singularity at the free end, a bound constraints the movement of the end nodes. The optimization problem is solved by the Augmented Lagrangian Multiplier method for ρ=1 (left) and ρ=10 (right). Comparing the evolution of the shape, it is clear that the design updates are more localized in the neighbourhood of the maximal stress when using a higher value of ρ.