Users:General FEM Analysis/Analyses Reference/Static Linear

From Carat++ Public Wiki
Jump to: navigation, search


Contents

General Description

The linear static analysis is applied to analyze displacements, strains or stresses of structures. This analysis is valid for linear static mechanical problems without any nonlinearity (geometrically nonlinear, contact, material nonlinear, ...). Static nonlinear problems can be solved by the static nonlinear analysis whereas transient problems are solved by dynamic analysis methods.

The static linear analysis formulates structural equilibrium on the initial configuration without consideration of deformations. Hence, it is only valid for problems showing small displacements.

Structure of Equation System

The linear static analysis solves the problem

K*U=F,

with the linear stiffness matrix K, the unknown displacement fields U and the right hand side vectors F. This system of equations is solved for the unknown displacements by a linear solver. In general, linear solvers may be separated in iterative and direct solvers. Direct solvers transform the stiffness matrix K into an upper diagonal matrix. The displacement field follow by a back substitution with the respective right hand side vector. This back substitution requires only small numerical effort which makes direct solvers very attractive if a couple of displacement fields have to be computed.


Input Parameters

Parameter Description

Compulsory Parameters
Parameter Values, Default(*) Description
SOLVER PC-SOLVER int Linking to a linear solver (direct or iterative)
OUTPUT PC-OUT int Linking to output objects (specifies the type of output format, e.g. GiD)
COMPCASE LD-COM int Linking to computation case objects which specify the boundary conditions (loading and supports)
DOMAIN EL-DOMAIN int Linking to the domain the analysis should work on
Optional Parameters
ONLY_IBRA_PRE int Get integration domain in JSON format for Isogeometric B-Rep Analysis (IBRA) (1 = true, 0 = false)
SIMULTANEOUS_EIGENVALUE_ANALYSIS int Simultaneous eigenvalue analysis (1 = true, 0 = false)
EIGEN_SOLVER PC-SOLVER int Linking to a eigenvalue solver
NUM_EIGEN_MODES int Number of eigenmodes

Example of a Complete Input Block

PC-ANALYSIS 1: STA_GEO_LIN
SOLVER = PC-SOLVER 5
OUTPUT = PC-OUT 1
COMPCASE = LD-COM 1,2,3
DOMAIN = EL-DOMAIN 1


Examples

A Full Example: Bending of a cantilever discretized with shell elements

The following example describes a simple cantilever problem discretized by SHELL8-elements. The respective input file can be found at

  • ..\examples\benchmark_examples\elements\shell8_quad_lin_canti_I\shell8_canti_2x20_elem_load.dat

The problem computes three computation cases (dead load, snow load and pressure load). The boundary conditions are visualized by the figure below.

Simple cantilever problem using SHELL8 elements

The basic goal of each linear static analysis is the computation of the displacement field. For load case 1 this result is depicted in the figure below, whereas the deformation in z-direction is additionally visualized by the color plot.

Displacement of cantilever problem

It can be seen that the support region does not show any deformation whereas the tip region deforms by a value of 8.76.

Often the stress distribution is visualized by color plots. Shell structures require the specification of the layer on which the stresses are computed. The picture below shows the first principle stress on the top of the cantilever.

First principle stress of cantilever problem (top layer)

It can be seen that the stresses show maximum values at the support region of the cantilever. At the tip they are nearly zero. In contrast to analytical results the stresses are not exactly zero in numerical models. The reason is the stress computation at the Gauss points. These points are situated inside the elements and not exactly at the tip of the cantilever.


Benchmark examples

  • Cantilever under different surface loads, discretized SHELL8-elements ..\examples\benchmark_examples\elements\shell8_quad_lin_canti_I\shell8_canti_2x20_elem_load.dat
  • Truss under tension discretized by SOLIDHEXA1-elements: ..\examples\benchmark_examples\analyses\stalin_cantilever_hexa_I\cbm_biegebalken.txt




Whos here now:   Members 0   Guests 0   Bots & Crawlers 1
 
Personal tools
Content for Developers